Powerful workhorse making short work of processing material.

With a 6 ft/1.83 m drum and a hopper that holds 6 cubic yards/4.6 cubic meters, the TR626 makes short work of processing material. Access the drum through removable side panels, drum end or top of the drum. Its 125 hp/93.2 kw John Deere 4045 Tier 4 Final is a powerful workhorse. Impressive 72.5 ft/22.1 m conveyor features self-cleaning tail pulley and return idlers.

REQUEST OFFER

PRODUCT VIDEOS

FEATURES & BENEFITS

STARTUP DELAY AND ALARM SYSTEMS
Enhance worker safety with startup delay and alarm systems that notify your whole crew when the machine is about to start.
TALL, WIDE THROAT OPENING
Move material smoothly without bridging, thanks to a tall, wide throat opening.
HEAVY-DUTY ROLLERS
Extend belt life even under tough loading conditions with closely set, heavy-duty rollers supporting the apron conveyor.
KEEP SCREEN WEIGHTS LOW
Keep screen weights low when processing wet materials by clamping on a smaller diameter tension screen wire and increasing screening area.
REDUCED SPILLAGE
Speed up your clean up because the flashing and sheeting fit tightly against the drum and conveyors to reduce spillage.
LOW HOPPER INFEED HEIGHT
Forget the loading ramps, since the 626 has a low hopper infeed height.

SPECIFICATIONS

Compare Models
Units:
  • Weight
    22543.5 kg
  • Hitch Weight
    7565.9 kg
  • Transport Length
    16.6 m
  • Transport Width
    287 cm
  • Transport Height
    4.1 m
  • Operation Length
    25.7 m
  • Operation Width
    287 cm
  • Operation Height
    4.8 m
  • Capacity
    Approximately 200 cu yd (152.9 cu m) per hour with .5" (1.3 cm) screens installed and material with moisture less than 40%
  • Make and Model
    John Deere PowerTech PVX 4.5L, 4045HFC93 Tier 4F
  • Number of Cylinders
    4
  • Engine Rating
    134 hp (93.2 kW) @ 2400 rpm, 398 ft-lb (531.6 Nm) of torque @ 1600 rpm
  • Fuel Tank Capacity
    276.3 L
  • Fuel Consumption
    3.5 gph (13.3 L/hr) under most operating conditions
  • Maximum Engine Operating Angle (Operating angles do not indicate safe machine operating angles)
    30 deg
  • Battery
    950 cold cranking amps
  • Oil Filter
    Spin-on
  • Recommended Oil
    Mobil 15/40
  • Oil Volume with Filter
    14.7 L
  • System Voltage
    12 V, 120 amp alternator
  • Air Cleaner
    Dual element oversized
  • Radiator Fan
    Suction-type
  • Operation
    62.9 gpm @ 2800 psi (238.1 L/min @ 172.4 bar [17240 kPa])
  • Tank capacity
    757.1 L
  • Frame Description
    4 independent hydraulic jacklegs
  • Axle/Suspension
    Leaf spring
  • Capacity
    10205.8 kg
  • Tires - Option One
    235-75R 17.5H qty. 4
  • Hopper Capacity
    4.6 cu m
  • Hopper Bottom Width
    121.9 cm
  • Apron Conveyor Speed
    0-205 fpm (0-62.5 m/min)
  • Apron Opening Height
    86.4 cm
  • Apron Opening Width
    109.2 cm
  • Hopper Height
    9.5' (2.9 m) from ground level at operating incline
  • Hopper Opening
    13.2' x 5.3' (4 m x 1.6 m)
  • Apron Conveyor Length
    4.9 m
  • Apron Conveyor Belt Width
    121.9 cm
  • Apron Conveyor Rollers
    4" (10.2 cm) diameter qty. 14
  • Drum Operation
    0-42.6 gpm (161.3 L/min)
  • Drum Motor
    48.8 cu in (800 cu cm) displacement
  • Drum Diameter
    1.8 m
  • Drum Support Description
    Four steel trunnion rollers 8 in (20.3 cm) diameter 4 in (10.2 cm) width
  • Drum Length
    7.9 m
  • Thrust Bearing Diameter
    12.7 cm
  • Thrust Bearing Face
    7.4 cm
  • Drum Speed
    0-21.6 rpm
  • Drum Drive Chain
    140 WT
  • Drum Angle Adjustability
    3-5 degrees
  • Maximum Screen Panels
    8
  • Brush Diameter
    35.6 cm
  • Bristle Material
    Polyethylene
  • Brush Assembly Support
    Two 1.25" (3.2 cm) sealed ball bearings
  • Conveyor Operation
    58.3 L/min
  • Conveyor Motor Displacement
    535.9 cu-cm
  • Fines Conveyor Length
    22.1 m
  • Fines Belt Speed
    123.4 m/min
  • Conveyor Belt Width
    91.4 cm
  • Conveyor Belt Type
    220 lb (99.8 kg), 2 ply, 2/16" x 1/16" (4.8 mm x 1.6 mm)
  • Conveyor Belt Stacking Height
    16.6' (5.1 m) with drum at 4 degrees
  • Head Pulley Type
    Rubber lagged, 12" (30.5 cm) diameter, 38" (996.5 cm) wide
  • Head Pulley Bearing
    2.5" (6.4 cm) pillow block
  • Rubber Flashing
    Adjustable, .25" (.64 cm) thick, 4" (10.16 cm)
  • Troughing Idler Type
    20 degrees CEMA "B" with permanently sealed bearings spaced at 24" (60.96 cm) centers
  • Self-Cleaning Tail Pulley Dimensions
    10" (25.4 cm) diameter, 38" (96.5 cm) wide with 2.4" (6.1 cm) shaft
  • Tail Pulley Takeup
    30.5 cm
  • Self-Cleaning Return Idlers
    11, each 4" (10.2 cm) diameter
  • Fines Conveyor Frame
    4" x 8" (10.2 cm x 20.3 cm) structural steel tubing
  • Overs Conveyor Length
    5.8 m
  • Maximum Variable Overs Belt Speed
    88.4 m/min
  • Conveyor Belt Size
    48" (121.9 cm) wide with raised crescent
  • Conveyor Belt Type
    220 lb (99.8 kg), 2 ply, 2/16" x 1/16" (4.8 mm x 1.6 mm)
  • Conveyor Belt Stacking Height
    3' (.9 m) x 10' (3.1 m)
  • Head Pulley Type
    Rubber lagged, 12" (30.5 cm) diameter, 38" (996.5 cm) wide
  • Head Pulley Bearing
    2.5" (6.4 cm) pillow block
  • Self-Cleaning Tail Pulley Dimensions
    10" (25.4 cm) diameter, 51" (129.5 cm) wide with 2.4" (6.1 cm) shaft
  • Tail Pulley Takeup
    30.5 cm
  • Solid Return Idler Size
    4" x 8" diameter
  • Overs Conveyor Frame
    4" x 8" (10.2 cm x 20.3 cm) structural steel tubing

LITERATURE

Related Products

-

Talk with a Vermeer expert today!

Fill the next form with your informations and in the fastest time an Vermeer representant will contact you .

Request offer

    FEATURES & BENEFITS SPECIFICATIONS PRODUCT VIDEOS Request offer
    Jump to...