Ciocan Hidraulic Mincon 8DH

Ciocanul hidraulic Mincon 8DH este proiectat folosind tehnologie dovedita a fi cu performanta de top acest lucru clasandu-se intre primele locuri, atunci cand le comparam cu alte utilaje similare din piață. Aceste instrumente sunt excelente pentru toate tipurile de foraj, incepand de la foraj pentru instalatiii geotermale rezidențiale, forajul pentru carierele de producție piatra, foraje seismice și foraje pentru construcții mici.

Caracteristici și beneficii cheie

  • Funcțiile patentate maximizează producția și reduc la minim partea de servisare
  • Datorita faptului ca nu are foarte multe componente interne nici piesele de schimb nu sunt foarte numeroase
  • Designul fără valve asigură o funcționare lina si optimizeaza procesul pentru o utilizare frecventa
  • Manșon pentru o rezistență optimă la uzură chiar și în cele mai vitrege si abrazive condiții.
  • Pozitionarea sistemului de montare in spatele ciocanului usureaza montarea si demontarea acestuia
  • Pozitionarea furtunelor, elimină nevoia de haine de schimb și instrumente speciale de asamblare.
  • Toate componentele interne critice sunt tratate termic sub control strict pentru a maximiza longevitatea uneltei.
  • Specificatii
  • Lista piese
  • Consumul de aer
  • Ungere
  • Drill Bits
  • Documente
Specificatii
Specificatii Metric Imperial
Diametrul exterior al ciocanului 181mm 7.15"
Lungime ciocan 1186mm 46.7"
Dimensiunea plata 140mm 5.5"
Coada tip burghiu DHD380
Dimensiunea minimă a biților 203mm 8.0"
Greutatea ciocanului 173.2Kgs 381Lbs
Greutatea forezei (216mm/8 1/2") 52.2Kgs 115Lbs
Greutate piston 39Kgs 86Lbs
Partea din spate 0.75mm 0.030"
Compozitie cuplu 8135-10850 NM 6000-8000 FT Lbs
Manson 172mm 6.770"
Limita 169mm 6.650"
Pachet cu aer minim recomandat 425 l/s @ 24.1 Bar 900 cfm @ 350 psi
Lista piese
Item # Numarul piesei Descriere
MD801AS01 Mincon 8DH (4 1/2" A.P.I. Reg. Pin)
1 MD801BH01 Backhead (4 1/2" A.P.I. Reg. Pin)
2 MD822OR01 Inel
3 MB506CH01 Clapa blanc
4 MD802CV01 Valva de verificare
5 MB503SP01 Arc
6 MD805LR01 Inel de blocare
7 MD804SM01 Inel de regenerare
8 MD807DR01 Distribuitor aer
9 MD821OR01 Inel
10 MD820OR01 Inel
11 MD809SR01 Sezut inel
12 MD808IC01 Cilindru interior
13 MD810PN01 Piston
14 MD811WS01 Manson
15 MD812PR01 Inel de blocare a pistonului
16 MD814BR01 Inel de retinere a bitilor
17 MD821OR01 Inel
18 MD815CK01 Cleste (DHD380)
19 MD826SK01 Kit Service
MD826SK01 Kit Service
3 MB506CH01 Clapa Blanc
MB506CH02 Clapa 1/8" (3.2mm)
MB506CH03 Clapa 3/16" (4.8mm)
5 MB503SP01 Arc
MD825OK01 Kit Inel
MD825OK01 Kit Inel
2 MD822OR01 Inel
9 MD821OR01 Inel
10 MD820OR01 Inel
17 MD821OR01 Inel
Consumul de aer

Air Pressures are given for compressors operating at seal level at 20° C (68º F). Corrections to actual compressor volume should be made to account for temperature, altitude and relative humidity.

Ungere

DTH hammers must receive a constant supply of proper rock drill oil to protect the internal components and to provide a good air seal between the hammer's running surfaces for efficient drilling. Mincon recommends the use of Mincon Envirosafe® Rock Drill Oil (RDO) to maintain optimal performance and extend the life of the internal components. The correct consumption of oil is dependent upon the air volume and conditions. Please refer to the lubrication graph below for recommendations. When drilling in wet conditions the normal amount should be doubled. There should be visual evidence of oil around the drill bit shank and within the tube joints when changing tubes.

If using petroleum based rock drill oils, the recommended grade of oil is dependent on the ambient temperature and the operating pressure. As a rule of thumb, ISO320 grade rock drill oil should be used whenever possible as the hammer is a high frequency tool, however, where the pump cannot pump the oil in colder conditions, a lower grade of oil can be used as per the graph below.

Drill Bits

Note: The Part Numbers below require the Carbide Insert type code to be added on the end to complete them. For a combination of carbide inserts use the gauge row code first and then the face code.

Documente

Vorbeste astazi cu un expert Vermeer.

Completeaza urmatorul formular cu informatiile tale si in cel mai scurt timp vei fi contactat de un reprezentant Vermeer.

Cere o oferta